VEC

Construction support / Decatur, TN

Coordinate the interfaces.

Coordinate the interfaces or the handoff. VEC connects unresolved drawing conditions to clear decisions and traceable revisions.

Construction project coordination in Decatur, TN for the place where drawings meet the physical job. We compare interfaces, record the question, and prepare information a contractor or client can use.

See the coordination scope Bring the unresolved set

Issue-led handoffConstruction coordination support starts with the current source information. A duct crossing a beam is a decision, not a note for later.

Exposed framing and service runs inside an unfinished building
Opening condition / unfinished interiorFIELD NOTE 00—01
00

Make the next drawing buildable.

We coordinate drawings before a ceiling closes, while a revision is still moving, or when the field crew has stopped at a junction that the set does not explain.

Our construction document coordination service is inquiry-only. We scope the work in USD after we understand the drawing volume, discipline count and requested review depth. There is no published rate and no binding online quote.

InputCurrent drawings, models and marked conditions
DecisionOne open question tied to its source
HandoffA revision-aware package for the next person

Three field stops

Read it. Resolve it. Issue it.

Our sequence stays close to the job. We do not turn a field photograph into an approval, and we do not pretend missing information is a clash.

Pipework, ductwork and cable trays above an open corridor ceiling
Open ceiling / interfaces before closure

01

Discipline coordination

We compare architectural, structural and building-services information at the points where one trade needs room from another. We separate an absent detail from two instructions that cannot both be followed.

Input
Current drawing set, discipline list, revision references and known field questions.
Output
A marked coordination record showing the interface, source references and decision still needed.
Price basis
Project-specific written scope in USD, based on discipline count and drawing volume.

Boundary. Required tolerances, loads and clearances come from project documents and responsible designers. Coordination does not authorize a field change.

Bring the unresolved set
Galvanized duct passing beside a steel beam connection
Constrained junction / question for review

02

Clash review

Our construction clash review narrows attention to documented junctions. We inspect the supplied drawings or model, name the conflict, and record the decision required instead of guessing at a structural solution.

Input
Supplied model or drawing set, identified junctions, photographs and the agreed review depth.
Output
An issue record that points back to the source view, sheet or detail and leaves approval with the responsible designer.
Price basis
Written review scope in USD, based on supplied model or drawing quality and agreed review depth.

Boundary. A field photograph alone does not establish a structural solution. The review does not promise that every clash will be found.

Bring the unresolved set
Construction drawing detail being checked on a temporary site trestle
Revision in use / information at the trestle

03

Contractor and client issue packages

Our contractor drawing package tells the next person which information is released, which revision is current, and what remains unresolved. We assemble a legible handoff instead of burying the decision in a long email chain.

Input
Drawings to issue, revision status, package audience, decision record and required issue milestone.
Output
Contractor and client issue packages with references, revision control and unresolved decisions visibly separated.
Price basis
Written package scope in USD, based on package size and required revision rounds.

Boundary. The package does not certify design, approve construction or replace the responsible designer's review.

Bring the unresolved set

Input ledger / 04

What a handoff needs.

Send us the current set, not the set you meant to issue. Mark what changed. A useful inquiry gives our review a starting point and keeps revision coordination tied to the actual job.

Tape measurement at a pipe sleeve in an unfinished concrete wall
A measurement is context. The drawing and responsible designer still control the requirement.
Current drawings
Sheet numbers, model views or document references that describe the condition now.
Revision status
Revision mark, issue date if supplied, and a plain note about what changed.
Known issues
The junction that stopped work, including a field photograph when it helps locate the question.
Issue milestone
Who needs the next package and what decision must be visible before it moves.

Keep approval in the right hands. Required tolerances, loads, clearances and field changes remain with the responsible designer. Send the information through the project inquiry form.

Ready when the set is current

Bring the unresolved set.

Tell us what stopped the handoff and what information exists now. Sending us an inquiry does not book work. We provide a written scope only after the project inputs and review depth are clear.

Bring the unresolved set
Phone(423) 334-1020Email[email protected]
Postal addressP.O. BOX 277 18359 HIGHWAY 58 NORTH, DECATUR, TN 37322